Split Pin for Driveshaft Nut - Fits Mitsubishi Colt/Mirage/Cyborg CJ4A 1.6 Mivec Fits both Front Driveshaft Castle Nuts
Mitsubishi Part Number MF472085
Split Pin for Driveshaft Nut - Fits Lancer GSR 1.8 Turbo's both CD5A and CM5A Fits both Front and Rear Outer Driveshaft Castle Nuts
Split Pin for Driveshaft Nut - Fits Legnum/Galant VR4's EC5W EC5A Fits both Front and Rear Outer Driveshaft Castle Nuts
Copper Washer to Caliper Banjo Bolt - Mitsubishi Various Models
Fits Most Models of Mitsubishi that use a Banjo Bolt to Front or Rear Caliper incl EVO, FTO, Lancer GSR, Various Colts, Galant/Legnum etc
Mitsubishi Part Number MA111832 MA111832C
Fuel Line Copper Washer - Various Mitsubishi Models incl FTO/EVO 1-6 /Colt CA5A/Lancer 1.8 GSR
2 Used on Banjo Bolt to Fuel Filter These are supplied with our Fuel Filters so no need to order if you have ordered a fuel filter.
Mitsubishi Part Number MB906711 MB906711C
Dust Cap Cover for Throttle Screw - Mitsubishi Lancer GSR 1.8 Turbo CM5A
Choose from Aftermarket Plastic Version or Genuine Mitsubishi
Plastic Cap is Shown Fitted in 2nd Picture
Mitsubishi Part Number MD614532
Crush Washer for Reverse Light Switch - Mitsubishi Lancer GSR 1.8 Turbo CM5A
Mitsubishi Part Number MF660035
Front or Rear Caliper Brake Nipple - Mitsubishi Lancer GSR 1.8 Turbo CD5A/CM5A Same part used on all GSR calipers. These are prone to corrosion, rounding off and snapping. Mitsubishi Part Number MB928290
Longer Wheel Stud for Mitsubishi Lancer GSR 1.8 Turbo CM5A These are usually used either when fitting wheels which have the wrong offset for the car and so you have to use a wheel spacer or widening the track of the vehicle using wheel spacers. Dimensions against OEM Stud are shown HERE Sold in Singles You need 4 per hub so 16 per car. Mitsubishi Part Number MB911495
Rear Upper Caliper Slider Tube Cap - Mitsubishi Lancer GSR 1.8 4WD Turbo CM5A These are the correct ones same type as the original ones that have a tiny hole to allow air and excess grease to escape. 1 used on the each Rear Caliper Mitsubishi Part Number N/A - Mitsubishi Do Not Sell Separate to Caliper
Turbo Oil Drain Pipe Gasket - Mitsubishi Lancer GSR 1.8 4WD Turbo CM5A also called turbo oil return pipe gaskets Sold in Singles (You need 1 for each end return pipe so 2 in total) Exploded Diagram Showing Locations Used HERE Mitsubishi Part Numbers MD050082 MD174244 MD194403 MD145171 MR258477
Fits on the Front Strut Top Mount of EVO 1-9, FTO's, Lancer 1.8T GSR's
3rd Picture on Listing Shows Location Fitted
Price is for ONE
Mitsubishi Part Number MB109960
THESE ARE DISCONTINUED BY MITSUBISHI - BUT WE HAVE STOCK
Apec - Brake Lubricant is ideal for your Lancer Brakes Grease is the word. Specially formulated copper-free lubricant Assists the smooth movement of braking components, and minimises noise Effectively withstands water and high temperatures Fully compatible with ABS brakes Supplied in a handy 75ml tube For use on Squeal Shims, Pad Ends where it touches caliper see Apec Bulletin Sheet HERE NB: Make sure you keep it away from friction surfaces, rubber seals and boots. Size 75ml Tube Apec Part Number BG75
Throttle Body to Inlet Manifold Bolts Used on Various Mitsubishi Models incl EVO, FTO, Lancers and Colts
Sold as a Set of 4 Bolts and Spring Washers
Choose From Genuine Mitsubishi or Aftermarket Copy
Location Used Shown HERE
Mitsubishi Part Numbers MF240064 MF241264
Grommit - Footrest - MR190315 - Fits various Mitsubishi Models incl EVO 456 - CJ4A Colt - CM5A Lancer
If the footrest is loose it's likely to be this grommit. Fits M/T and A/T Models where applicable. ONE Required per vehicle.
Exploded Diagram HERE
Mitsubishi Part Number MR190315
Magnetic Sump Plug - Mitsubishi M14 x 1.5
Fits all Mitsubishi Models that use OEM Part Number MD050316
Anodized Red Alloy Sump Plug with Sump Washer.
Gives advance warning of engine problems as it catches any steel flakes from engine wear on the megnetic end.
This is designed to be used with Normal Grease to form a layer between the Steel Sump and the Alloy Sump Plug. DO NOT FIT WITHOUT GREASE ON THE THREADS
This also fits various Suzuki Models that use a M14 x 1.5 Sump Plug.
MD050316, MD050317 09247-14044-000 S1 | 09247-14044 S1
Lower Injector Seal/Insulator - Mitsubishi Lancer 1.8 GSR 4WD Turbo CM5A Location fitted shown on Exploded Diagram HERE Mitsubishi Part Number MD087060
Oil Pump Spring - MD015988 - Lancer 1.8 Turbo GSR CD5A CM5A
Exploded Diagram Showing Location Fitted HERE
Mitsubishi Part Number MD015988
Rear Brake Line P Clip MB344587 - Mitsubishi Lancer GSR 1.8 Turbo CM5A
Choose from Genuine Mild Steel Mitsubishi Part or Stainless Aftermarket Copy
Locations Used Shown Here
Mitsubishi Part Number MB344587 (Was MB316285)
Half Moon Seal - Mitsubishi Lancer GSR 1.8 4WD Turbo CM5A Exploded Diagram HERE Mitsubishi Part Number MD050536
Valve Spring - Mitsubishi Lancer GSR 1.8 Turbo CM5A
Genuine Mitsubishi Valve Spring Sold in Singles - You need 16 per Engine
Mitsubishi Part Number MD163358
Gasket for Brake Servo/Booster - Various Mitsubishi Models incl EVO/FTO/Lancer GSR/Legnum/Colt
Location used is between the Servo/Booster and Body See HERE
Mitsubishi Part Number MB928711 was MB238089
Square parking brake retaining clip - Mitsubishi Lancer GSR 1.8 4WD Turbo CM5A This little clip holds the cable onto the rear brake caliper. One clip used on each cable. Mitsubishi Part Number MB520216
Good Quality Aftermarket Copy of Sump Plug and Washer Fits Mitsubishi Lancer 1.8 GSR 4WD CD5A CM5A Mitsubishi Part Number Copies of MD050316 MD050317
Oil Pump O Ring - Mitsubishi Colt/Mirage 1.6 Mivec CJ4A
Mitsubishi Part Number MD163246
Oil Pump O Ring - Lancer 1.8 Turbo GSR CD5A CM5A
Locations on Both Vehicles Shown HERE
Upper Injector O-Ring - Mitsubishi Lancer GSR 1.8 Turbo 4WD CM5A Exploded Diagram Showing Location Fitted HERE Mitsubishi Part Number 1465A188 was MD614813 also MD620787
