Split Pin for Driveshaft Nut - Fits Lancer GSR 1.8 Turbo's both CD5A and CM5A Fits both Front and Rear Outer Driveshaft Castle Nuts
Mitsubishi Part Number MF472085
Copper Washer to Caliper Banjo Bolt - Mitsubishi Various Models
Fits Most Models of Mitsubishi that use a Banjo Bolt to Front or Rear Caliper incl EVO, FTO, Lancer GSR, Various Colts, Galant/Legnum etc
Mitsubishi Part Number MA111832 MA111832C
Fuel Line Copper Washer - Various Mitsubishi Models incl FTO/EVO 1-6 /Colt CA5A/Lancer 1.8 GSR
2 Used on Banjo Bolt to Fuel Filter These are supplied with our Fuel Filters so no need to order if you have ordered a fuel filter.
Mitsubishi Part Number MB906711 MB906711C
Wheel Nut - Bulge Nut - Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A This fits the wheels that the vehicle came out of the factory with. You can choose from aftermarket copy or Original Mitsubishi Mitsubishi Part Number MB057636 3880A008 MR910032 3880A009
Genuine Mitsubishi Crushable sump plug washer. This is the best type of washer to seal the sump plug. Folded edge so it seals properly therefore it doesn't weep oil like cheap copper washers. It is only pence more expensive. Inner diameter = 14mm Outer diameter = 20mm Thickness = 2mm Mitsubishi Part Number MD050317
Crush Washer for Reverse Light Switch - Mitsubishi Lancer GSR 1.8 Turbo CD5A
Locations Used HERE
Mitsubishi Part Number MF660035
Front or Rear Caliper Brake Nipple - Mitsubishi Lancer GSR 1.8 Turbo CD5A/CM5A Same part used on all GSR calipers. These are prone to corrosion, rounding off and snapping. Mitsubishi Part Number MB928290
Longer Wheel Stud for Mitsubishi Lancer GSR 1.8 Turbo CD5A These are usually used either when fitting wheels which have the wrong offset for the car and so you have to use a wheel spacer or widening the track of the vehicle using wheel spacers. Dimensions against OEM Stud are shown HERE Sold in Singles You need 4 per hub so 16 per car. Mitsubishi Part Number MB911495
Rear Upper Caliper Slider Tube Cap - Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A These are the correct ones same type as the original ones that have a tiny hole to allow air and excess grease to escape. 1 used on the each Rear Caliper Mitsubishi Part Number N/A - Mitsubishi Do Not Sell Separate to Caliper
Turbo Oil Drain Pipe Gasket - Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A also called turbo oil return pipe gaskets Sold in Singles (You need 1 for each end return pipe so 2 in total) Exploded Diagram Showing Locations Used HERE Mitsubishi Part Numbers MD050082 MD174244 MD194403 MD145171 MR258477
Fits on the Front Strut Top Mount of EVO 1-9, FTO's, Lancer 1.8T GSR's
3rd Picture on Listing Shows Location Fitted
Price is for ONE
Mitsubishi Part Number MB109960
THESE ARE DISCONTINUED BY MITSUBISHI - BUT WE HAVE STOCK
Apec - Brake Lubricant is ideal for your Lancer Brakes Grease is the word. Specially formulated copper-free lubricant Assists the smooth movement of braking components, and minimises noise Effectively withstands water and high temperatures Fully compatible with ABS brakes Supplied in a handy 75ml tube For use on Squeal Shims, Pad Ends where it touches caliper see Apec Bulletin Sheet HERE NB: Make sure you keep it away from friction surfaces, rubber seals and boots. Size 75ml Tube Apec Part Number BG75
Magnetic Sump Plug - Mitsubishi M14 x 1.5
Fits all Mitsubishi Models that use OEM Part Number MD050316
Anodized Red Alloy Sump Plug with Sump Washer.
Gives advance warning of engine problems as it catches any steel flakes from engine wear on the megnetic end.
This is designed to be used with Normal Grease to form a layer between the Steel Sump and the Alloy Sump Plug. DO NOT FIT WITHOUT GREASE ON THE THREADS
This also fits various Suzuki Models that use a M14 x 1.5 Sump Plug.
MD050316, MD050317 09247-14044-000 S1 | 09247-14044 S1
Oil Pump Spring - MD015988 - Lancer 1.8 Turbo GSR CD5A CM5A
Exploded Diagram Showing Location Fitted HERE
Mitsubishi Part Number MD015988
Rear Brake Line P Clip MB344587 - Mitsubishi Lancer GSR 1.8 Turbo CD5A
Choose from Genuine Mild Steel Mitsubishi Part or Stainless Aftermarket Copy
Locations Used Shown Here
Mitsubishi Part Number MB344587 (Was MB316285)
Transfer Box Centre O Ring - Mitsubishi Lancer GSR 1.8 Turbo CD5A Exploded Diagram Showing Location HERE Mitsubishi Part Number MF520414
Half Moon Seal - Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A Exploded Diagram HERE Mitsubishi Part Number MD050536
Gasket for Brake Servo/Booster - Various Mitsubishi Models incl EVO/FTO/Lancer GSR/Legnum/Colt
Location used is between the Servo/Booster and Body See HERE
Mitsubishi Part Number MB928711 was MB238089
Oil Filter - Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A Aftermarket engine oil filter Exploded Diagram HERE Mitsubishi Part Number 1230A153 MD322508 MD136466 MD031805 MD071462 MD135737 MD332687 MD365876
Oil Pump O Ring - Lancer 1.8 Turbo GSR CD5A CM5A
Locations on Both Vehicles Shown HERE
Mitsubishi Part Number MD163246
Transfer Box Outer Cover O Ring - Mitsubishi Lancer GSR 1.8 Turbo CD5A Exploded Diagram Showing Location HERE Mitsubishi Part Number MD727944
Wheel stud for Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A These are easily damaged by overtightening. Overtightening pulls the threads in such a way that when unscrewed to remove it drags the threads up the shaft and either sticks solid or shears the stud off. Mitsubishi Part Number MB911495 MB303869
Fits Frontpipe to Turbo Elbow & either side of the catalytic converter on Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A 4G93T Two are used on the catalytic converter & one on the frontpipe to turbo elbow. See Exploded Diagram HERE Mitsubishi Part Number MB687002
Wynn's Engine Flush 425ml
Leaves engines clean, ready for new oil to circulate freely. Helps free sticking valves and piston rings. How to use Add entire contents to the engine oil One bottle treats up to 6 liters of engine oil For better results, use at each oil change Bring engine to operating temperature. Switch off engine. Add one bottle of 425 ml to up to 6 litres engine oil before each oil change. Let the engine run for 20 minutes. Change oil and filter.
Banjo Bolt to Front Brake Caliper - MU001458
Fits Various Mitsubishi Models (NOT Brembo Caliper Models)
Unlike a normal Banjo Bolt - These do not have holes in them, they have grooves for the brake fluid to flow along and not having holes in them makes them stronger and less likely to snap. Price is For ONE
Mitsubishi Part Number MU001458 Was MR249625
Rubber Insulator for Propshaft Bearing - Mitsubishi Lancer 1.8 Turbo GSR CD5A These are a steel washer with a rubber surround, the rubber can perish and allow movement of the propshaft bearing. There are Four of these used on the propshaft bearing. See HERE Mitsubishi Part Number MB837586
Lash Adjusters/Hydraulic Tappets x 1 for Mitsubishi Lancer GSR 1.8 4WD Turbo CD5A Choose from 1, 8 or Full Set of 16 These are the later type with over 3mm oil hole. Exploded Diagram HERE Each and every Tappet is inspected for defects, hole size etc These are quality manufactured parts unlike some of our competitors We buy in the 1000's to get the best possible price. We then inspect each and every one for correct operation, hole size & burrs/poor finish. If any defects are found the tappet is discarded. Tappet Info & Bleeding Instructions HERE & HERE New Tappets Rarely Need Bleeding Mitsubishi Part Numbers MD376687 MD377239 MD171130 MD359419